Anti Wrinkle Installation Tube Pipe Bending Machine For Madical Bed
-- Mechanical features
1. High performance middle size pipe bending machine, with NC
control, multi-groups program and multi angles setting, it makes
your operation and setting convenient.
2. Widely used in mass production and standard products, such as
blast pipe, seat, fender guard and all the steel furniture.
3. The machine is NC control and hydraulic drive, it can have
different bending degrees to prefabricate.
4. PLC control and the machine runs steadily.
5. It has various functions can be chosen, such as manual
operation, automatic, semi-circulation, full-circulation and
6. Two angle setting, 0° to 185° is chosen at will. It can choose
an angle or two angles continuously.
7. Mobile type foot switch with three functions, auto start,
emergency stop, going on after emergency stop.
8. The safety is high.
9. Large volume cooling circulation system to make the machine run
10. Model exchanging is simple and convenient to be in flexible
11. The designing of the machine head and pipe bending precision is
high and the bending space is large.
-- Installation points
1. Bending die installation
Plunge the elbow in a clockwise direction and cap it. Replace the
required elbow wheel die and tighten the cap.
2. Clamp mold installation
Insert the clamping die with adjusting bolts, adjusting plates and
cover plates into the clamping die holder and connect the adjusting
bolts. The clamping die of the adjusting plate, cover plate, etc.
is inserted into the clamping die holder and the adjusting plate is
inserted. Fix on the clamp mold base and rotate the adjusting bolt
so that the center of the clamp mold and the center of the bend
tube mold are on the same plane. Then adjust it as follows:
2.1. Loosen the clamping bolts and press the manual “Pinch” button
until the clamped mold reaches the end point (there is a gap
between the bending tube mold and the clamping mold).
2.2. Adjust the clamping mold seat adjustment screw so that the
clamping mold and the bending tube mold are fully compressed.
2.3. Press the “Retreat” button to retract the clamping mold, and
then turn the clamping mold adjustment screw into about 1/4-1/2
2.4. Lock the clamping block fixing bolt.
3. Skateboard die adjustment method ditto
4. Mandrel and cylinder installation
4.1. Screw the mandrel onto the mandrel screw and fix the mandrel
to the proper position to fix the nut.
4.2. Relax the mandrel cylinder bolts.
4.3. The pointer of the moving mandrel cylinder block is related to
the scale of the rail holder and the radius of the elbow.
4.4. Lock the mandrel and cylinder.
5. Anti-crease device
The wrinkle-resistance mold is mounted on the wrinkle-proof plate
seat, and it can be properly adjusted as shown in the figure by 1°
6. Bending angle adjustment
The bend angle control is controlled by a proximity switch, a scale
display is shown at the adjustment position of the proximity
switch, and the proximity switch adjustment block is adjusted to a
Above is the first angle, below is the second angle, corresponding
to the angle/double angle selection on the operation panel, after
the trial bend and then trim the angle. Because the material of the
pipe is different, the rebound amount is also different. After the
adjustment is completed, the locking screw lock nut on the nut will
7. Overflow valve pressure adjustment
Press any of the manual buttons of pinch tube, back clamp, core,
and back core to release the pressure displayed on the pressure
gauge. At this time, rotate the pressure relief handle of the
overflow valve to adjust the pressure to the desired pressure of 10
MPA. The bending resistance should not be too high, so as not to
increase the oil temperature and to accelerate the wear of
-- Main application
Adapted material: steel pipe, stainless steel, copper pipe,
House structure, shipyards, automobile production, industrial
pipeline equipment, pulp, paper, chemicals, boilers, pump stations,
site fresh water and wastewater systems, municipal heating and
cooling systems, urban gas pipelines, municipal works such as
hospitals, office buildings, construction and large-scale public
buildings, medium and large-scale industries for maintenance and
repair work, power stations, installation companies, automatic fire
sprinkler systems in front of workshops.
-- Specifications of machine
|Maximum applicable carbon steel pipe||Φ75*3.0t|
|Maximum applicable stainless steel pipe||Φ63*3.0t|
|Maximum applicable copper pipe||Φ89*3.0t|
|Maximum coring length||2800mm|
|Maximum bending radius||300mm|
|Maximum bending angle||190°|
|Settable bending pipe number of each pipe fitting||15|
|Maximum oil pressure||14MPa|
-- Packaging and service
1. Payment terms: 30% T/T down payment and 70% T/T before shipment.
2. Delivery time: No later than 15 days since receiving the advance
3. Validity of the price: For ONE month.
4. Package: Wooden case.
5. Warranty period: We guarantee machine quality for 12 months.
During this period, if spare parts of the machine were damaged, we
can send the component to the customer by international express
-- Pictures of machine